List Price: $49.95
Your Price: $30.53
You Save: $19.42 (39 %)
Tension Bolt Washer Removal Tool
|
Your Price: From $64.10 to $140.13
1 piece Solid Dowel Pin, pick your engine and choice of 1 or 2 pins. Take advantage of Pair pricing! We have updated the Solid pins for better strength by reducing the puller thread to M8 x 1.25. This greatly strengthens the "rear" of the pin!
|
List Price: $97.30
Your Price: 49.95
Excentric Shaft Turning Tool
|
List Price: $101.45
Your Price: $75.99
You Save: $25.46 (25 %)
Handy tool for correctly sanding the angle of .7mm and 1mm side seals as you fit them to their individual groove.
|
List Price: $157.99
Your Price: From $9.95 to $126.95
6 Port Insert, no sleeve. Internal lock holds insert in place without drilling or tapping. prices per pair (2)
|
Replacment set of metric expansion plug (aka Freeze Plugs) for all RX-7 Rotary Engines.
|
Use these plugs to block the oil metering injection bungs in the rotor housings when running premix or other alternative means to lubricate the engine internals. Kit includes 2 plugs.
|
Fits 1974-85 12A/13B, Reusable. Kit includes inner/outer coolant seals, dowel pin(4), oil pedestal(4), ft. cover(1), rear stationary gear o rings and tension bolt washers (20).
|
List Price: $55.69
Your Price: $32.44
You Save: $23.25 (42 %)
Main Bearing for all rotary engines prior to 1993 and the '04-'08 RX8, low hp engine(a/t). Two required per 2-rotor engine.
|
|
List Price: $57.02
Your Price: $38.97
You Save: $18.05 (32 %)
13B Rotor Bearing. Technically this is a different part than the 13B-REW in the 3rd Gen FD RX-7, but you can get away substituting this significantly less expensive part.
|
These are the thicker 1.0mm thick side seals used from 1974 through 1985, both 12A and 13B applications. They come a bit long, so you need to file/sand them down to fit. Sold individually. Order 12 for a 12A or 13B 2-rotor engine.
|
These are the springs for the thicker 1.0mm thick side seals used from 1974 through 1985, both 12A and 13B applications. Sold individually. Order 12 for a 12A or 13B 2-rotor engine.
|
Front Main Seal. Installs in front cover to prevent oil from leaking past the eccentric shaft. Always replace. One required per engine. This is technically the 2nd gen FC and earlier part, but they work fine for 3rd gen FDs (13B-REW) as well.
|
List Price: $14.16
Your Price: $11.72
You Save: $2.44 (17 %)
Rear Main Seal for all RX-7s. Replace any time you remove flywheel.
|
List Price: $7.88
Your Price: $4.25
You Save: $3.63 (46 %)
|
List Price: $138.98
Your Price: $77.08
You Save: $61.90 (45 %)
|
List Price: $180.60
Your Price: $130.23
You Save: $50.37 (28 %)
|
Overhaul your mechanical Oil Metering Pump (pre-89) quickly and easily with the overhaul kit and instructional DVD.
|
List Price: $14.16
Your Price: $11.72
You Save: $2.44 (17 %)
Fits 84/85 GSL-SE 13B and earlier 13Bs.
|
List Price: $142.61
Your Price: $107.49
You Save: $35.12 (25 %)
|
List Price: $16.95
Your Price: $14.08
You Save: $2.87 (17 %)
Oil Galley Plug kit includes 2 large and 1 small replacement oil galley plugs.
|
Stock 1978-91 rear oil pressure regulator modified for higher pressure. We provide a regulator and modify it to your requirements from 70psi to 95psi.
|
List Price: $69.65
Your Price: $42.37
You Save: $27.28 (39 %)
Water Pump, New Cast iron for 1974-85 all
|
List Price: $131.90
Your Price: $128.95
You Save: $2.95 (2 %)
***HOLIDAY SPECIAL*** Oil Regulator test tool for safely and accurately modifying and testing of the rear oil pressure regulator for all years.
| | |